Product Name :
ALLOY 500 (UNS N05500)
Characteristics
− Nickel-copper alloy 500 combines the excellent corrosion resistance characteristic of alloy 400 with the added advantages of greater strength and hardness. The increased properties are obtained by adding aluminum and titanium to the nickel-copper base, and by heating under controlled conditions so that submicroscopic particles of Ni3 (Ti, Al) are precipitated throughout the matrix. The thermal processing used to effect precipitation is commonly called age hardening or aging.
− The corrosion resistance of alloy 500 is substantially equivalent to that of alloy 400 except that, when in the age-hardened condition, alloy 500 has a greater tendency toward stress-corrosion cracking in some environments.
− Alloy 500 has been found to be resistant to a sour-gas environment. After 6 days of continuous immersion in saturated (3500 ppm) hydrogen sulfide solutions at acidic and basic pH's (ranging from 1.0 to 11.0), U-bend specimens of age- hardened sheet showed no cracking. There was some tightly adherent black scale. Hardness of the specimens ranged from 28 to 40 Rc.
− The combination of very low corrosion rates in high-velocity sea water and high strength make alloy 500 particularly suitable for shafts of centrifugal pumps in marine service. In stagnant or slow-moving water, fouling may occur followed by pitting, but this pitting slows down after a fairly rapid initial attack.
Nickel Alloys 400
Characteristics
− Nickel-copper alloy 400 is a solid-solution alloy that can be hardened only by cold working. It has high strength and toughness over a wide temperature range and excellent resistance to many corrosive environments.
Typical Applications
− Alloy 400 is widely used in many fields, especially marine and chemical processing. Typical applications are valves and pumps; pump and propeller shafts; marine fixtures and fasteners; electrical and electronic components; springs; chemical processing equipment; gasoline and fresh water tanks; crude petroleum stills; process vessels and piping; boiler feed water heaters and other heat exchangers; and deaerating heaters
a. The ranges shown are composites for various product sizes and therefore are not suitable for specification purposes. Hardness values are suitable. For specification purposes providing tensile properties are not also specified.
b. Properties on request.
c. Properties shown are for sizes from 0.032 to 0.250 in diameter. Properties for other sizes may vary from these
Typical Applications
− Typical applications for alloy 500 are pump shafts and impellers; doctor blades and scrapers; oil well drill collars and instruments; electronic components; springs; and valve trim.
Alloy E52100
Characteristics
− This high carbon, chromium alloy is stocked in the annealed condition.
− This grade is manufactured by the electric furnace process. Typically the quenched hardness is 62 to 66 HRC depending mainly upon section thickness
Typical Applications
− Grade E52100 is used primarily for races and balls or rollers of rolling-element (anti-friction) bearings. The grade is also suitable for parts requiring high hardness and wear resistance
Typical Mechanical Properties (Annealed)
− Yield – 85,000 psi
− Tensile – 105,000 psi
− Elongation – 17%
− Reduction Area – 50%
− BHN at surface– 228
Typical Fittings in Stainless Steel and Exotic Alloys Inconel 600 N06600 Inconel 690 N06690
Plate Types
Carbon & HSLA
Alloy – Commercial Grades, Military Armor,
Aircraft Quality, Tool Steel
Duracorr® (12% Chromium Stainless)
Cut-To-Length Plate
Floor Plate (Sure-Foot®)
Range – Most Complete Size Range
Thickness
Carbon/HSLA – 3/16" to 30"
Alloy – 1/8" to 15"
Widths – up to 195" wide
Lengths – up to 1525" and longer
Pattern weights – up to 100,000 lbs.
Refer to size charts in back of this guide
Multiple Rolling Locations
Burns Harbor, IN
Coatesville and Conshohocken, PA
Melting Facilities
Riverdale, IL, Indiana Harbor, IN,
Cleveland, OH and Burns Harbor, IN
Blast Furnaces/Basic Oxygen Furnaces
6" or 10" Strand Cast Slabs
Coatesville, PA
Electric Furnace Melting
9" or 12" Strand Cast Slabs; Bottom Poured Ingot Casting
Ladle Refining/Low Sulfur Calcium Inclusion Shape Control
Vacuum Degassing
VOD Unit – Duracorr® Stainless Melting
Rolling Mills
Burns Harbor, IN - 3/16" to 4", up to 150" wide
TMCP (Thermal-Mechanical Controlled Processing)
Precise Weight Plate
Coatesville, PA – 3/16" to 30", up to 195" wide
Conshohocken, PA
1/8" to 1" Alloy and
3/16" to 2" Carbon, up to 100" wide
Discrete and Coil
Heat Treatment
Normalizing, Normalize and Temper
Quench & Temper
Annealing, Spherodize Anneal
Stress Relieving
Special Non-Standard Cycles
Testing
Tensile, CVN Impacts, Drop Weight
Through Gauge Testing, Dynamic Tear
HIC Testing (Hydrogen Induced Cracking)
Cleanliness (Aircraft Quality)
Ultrasonic Testing, Step-Cooling
Magnetic Particle Testing
Quick Plate Program
Coatesville and Conshohocken, PA
See Daily Inventory Listings
Plate Coils
84" to 96" Wide
3/16" to 5/8" Thick
Carbon and HSLA
Flame Cutting
Oxy-fuel and Plasma
Circles, Rings, Sketches, Strips
Special Plate And Flamecut Tolerances
Thickness
Width and Length
Camber
Flatness
Surface Preparation
Blasting
Painting
Oiling
Mill Edge
Improved Customer Yields
Certifications
ISO 9001:2008, ABS, PED
ISO 14001:2004
ISO 18001:2007
1.Product information of steel elbow
| Brand Name | Best Pipeline |
| Product Name | 90D Elbow |
| Certification | SGS/BV/ABS/LR/TUV/DNV/BIS/API/PED |
| Place of Origin | Shanghai China (Mainland) |
|
Material |
ASTM | Carbon steel(ASTM A234WPB,,A234WPC,A420WPL6. |
| Stainless steel(ASTM A403 WP304,304L,316,316L,904l,321. 1Cr18Ni9Ti, 00Cr19Ni10,
00Cr17Ni14Mo2, ect.) |
Alloy Steel:A234WP12,A234WP11,A234WP22,A234WP5,
A420WPL6,A420WPL3 |
|
DIN | Carbon steel:St37.0,St35.8,St45.8 |
| Stainless steel:1.4301,1.4306,1.4401,1.4571 |
| Alloy steel:1.7335,1.7380,1.0488(1.0566) |
|
JIS | Carbon steel:PG370,PT410 |
| Stainless steel:SUS304,SUS304L,SUS316,SUS316L,SUS321 |
| Alloy steel:PA22,PA23,PA24,PA25,PL380 |
|
GB | 10#,20#,20G,23g,20R,Q235,16Mn, 16MnR,1Cr5Mo,
12CrMo, 12CrMoG, 12Cr1Mo |
| Standard Specification | ASTM,JIS,BS,DIN,UNI etc. |
| Connection | Welding |
| Shape | Equal |
| Technics | Casting |
| Qualification | ISO9001, API,CE |
| Equipment | Pushing Machine,Beveling Machine,Sand Blasting Machine |
| Thickness | Sch10-Sch160 XXS |
| Size | Seamless 1/2" To 24" Welded 24" To 72" |
| Surface of Finish | Antirust Oil,Hot Galvanized and Polish |
| Pressure | Sch5--Sch160,XXS |
| Standard | ASME,ANSI B16.9; DIN2605,2615,2616,2617,JIS B2311 ,2312,2313; EN 10253-1 ,EN 10253-2 |
| The third party inspection | BV, SGS, LOIYD, TUV, and other party alloyed by clients. |
| Remark | Also can supply IBR fittings and Specialized NACE & HIC Fittings |
| Marking | Registered logo,Heat Number,Steel Grade,Standard,Size |
| MinimumOrder Quantity | 1pcs |
| Supply Ability | 800Tons per month |
| Price | Depending on quantity |
| Payment Terms | T/T or Western Union or LC |
| Supply Ability | 3,0000pcs per month |
| Delivery Time | 7-15 days depending on quantity |
| Packing | PLY-wooden case or pallet or as for clients' requirements |
| Application | Petroleum, chemical, machinery, electric power, shipbuilding, papermaking, |
|
Advantages | 1. 20 + years of production experience at your service.
2. The fastest delivery
3. The lowest price
4. Most comprehensive standards and materials for your choice.
5. 100% export.
6. Our products EXPORT to Africa, Oceania, mid east, eastern Asia, Western Europe etc. |
| Special design available as the requirement of customer |
2:Butt Welding Fittings in the following forms
Elbows 45o and 90o – long radius is standard; short radius is also available
Return bends 180o – long radius is standard; short radius is also available
Reducers – concentric and eccentric
Tees – equal and reducing
Caps
Stub ends – Type B, to MSS SP-43
Butt welding fittings can be supplied in either seamless or welded construction and are covered by
specification ASTM A403M (or ASTM A815M for Duplex grades) and ASME B16.9
3:Product Show
Product Tags:
|
|
Durable Stainless Steel Fittings Nickel Copper Alloy 500 Excellent Corrosion Resistance Images
|
